RPM 80245 Front A-Arms Blue Monster Jam/Rustler/Stampede/Slash 2

#ad
#ad
HRP (Level 3 Products) RPM80245 #ad - Key featuresnearly 25% lighter than stockstronger material resists flexing and breakingIncreased clearance in outer area of arms For use on the e-rustler, Monster Jam, Stampede, and Slash. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

. Rpm is a proud american manufacturer designing and manufacturing 100% of our molded products right here in the United States. Backed by rPM's world-renowned breakage warranty.

More information about HRP (Level 3 Products) RPM80245 #ad

RPM 80185 Rear A-Arms Blue E- Monster Jam, Rustler, Stampede

#ad
#ad
HRP (Level 3 Products) RPM80185 #ad - For use on the e-Rustler, Stampede, and Monster Jam. Rpm slash rear a-arms use stock suspension geometry and include stock rear toe angles. Rpm slash rear a-arms are not only stronger and more durable than stock, they are also more rigid and less flexible too, making them the perfect addition to those race-level Slashes on the track.

. These a-arms are backed by our limited lifetime warranty against breakage as well for confidence-inspiring durability and performance. Even after all of the increased muscle has been factored in, our a-arms still come in at over 10% lighter than the original arms! Our final design task was to improve the fit and finish and what we came up with will eliminate most of the slop in the rear suspension system! The Slash owner can tighten things up to near perfect out back simply by adding in a set of our #80382 Rear Bearing Carriers currently available.

Rpm is a proud american manufacturer designing and manufacturing 100% of our molded products right here in the United States. Additionally, the new geometry design leaves no place for dirt and rocks to get caught in the lower A-arm and reduces the chances of rocks and debris getting stuck between the axle and the arm.

RPM 80185 Rear A-Arms Blue E- Monster Jam, Rustler, Stampede #ad - Rpm slash rear A-arms are sold in pairs. Backed by rPM's world-renowned breakage warranty. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede. Overviewrpm rear a-arms for the traxxas Slash are designed specifically for the Slash - they are not multi-platform A-arms like the stock versions.

More information about HRP (Level 3 Products) RPM80185 #ad


Similar products



RPM 80595 Rear A-Arms Blue Slash Blue

#ad
#ad
HRP Distribution RPM80595 #ad - Rpm is a proud american manufacturer designing and manufacturing 100% of our molded products right here in the United States. Backed by rPM's world-renowned breakage warranty. The upper axle carrier hole. Overviewrpm rear a-arms for the traxxas Slash are designed specifically for the Slash - they are not multi-platform A-arms like the stock versions.

Our first design challenge was to beef up our version of the Slash rear A-arms to handle some serious abuse. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede. Even after all of the increased muscle has been factored in, our a-arms still come in at over 10% lighter than the original arms! Our final design task was to improve the fit and finish and what we came up with will eliminate most of the slop in the rear suspension system! The Slash owner can tighten things up to near perfect out back simply by adding in a set of our #80382 Rear Bearing Carriers currently available.

RPM 80595 Rear A-Arms Blue Slash Blue #ad - The material around the inner and outer hinge pins has been increased by a whopping 64%! We then eliminated all of the unnecessary holes and shock mounts that would be needed on other vehicles but not on the Slash, which significantly reduced the weight of our A-arms while improving crash durability. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used.

Backed by rPM's world-renowned breakage warranty. Additionally, the new geometry design leaves no place for dirt and rocks to get caught in the lower A-arm and reduces the chances of rocks and debris getting stuck between the axle and the arm. Rpm slash rear A-arms are sold in pairs.

More information about HRP Distribution RPM80595 #ad


Similar products



RPM Wide Front Bumper Black Rustler, Stampede, Bandit, Blue

#ad
#ad
HRP Distribution RPM81165 #ad - Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA! For the Slash 2WD. Backed by rPM's world-renowned breakage warranty. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede.

The upper axle carrier hole. Rpm designed this bumper with the backyard basher in mind by making it with our guaranteed unbreakable blend of nylons and is molded in black to give it that stock-looking appearance, or in optional blue or green to match the line of Grave Digger and Son-Uva-Digger chassis and body paint schemes.

RPM Wide Front Bumper Black Rustler, Stampede, Bandit, Blue #ad - For use on the e-Rustler, Stampede, and Monster Jam. Give that traxxas nitro or electric Rustler, Stampede, Nitro Sport or Bandit added protection with the RPM wide front bumper. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. These bumpers will help reduce front end damage during head on collisions with curbs, trees, etc.

Nothing surpasses the protection gained when your Traxxas vehicle is protected with an RPM wide front bumper! Replaces weaker stock components. This bumper stands six inches wide and adds an extra 1-1/2" worth of bulletproof, protection to the front end of the vehicle.

More information about HRP Distribution RPM81165 #ad


Similar products



RPM Traxxas Sealed Gear Cover, Blue

#ad
#ad
HRP Distribution RPM80525 #ad - We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper / wheelie bar mount as well. More clearance for larger pinions for owners hungry for speed. Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter.

Backed by rPM's world-renowned breakage warranty. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. For the Slash 2WD. Designed to increase durability. Proudly made in the USA. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm.

RPM Traxxas Sealed Gear Cover, Blue #ad - Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA! Sleek contours that would look great on any vehicle. The upper axle carrier hole.

For use on the e-Rustler, Stampede, and Monster Jam. Completely sealed.

More information about HRP Distribution RPM80525 #ad


Similar products



RPM 80375 Front Bearing Carriers for Slash 2WD, Nitro Slash, E-Rustler and E-Stampede 2WD, Blue

#ad
#ad
HRPAA RPM80375 #ad - Bearings are not included with these kits 4 bearings are needed for each kit. Designed to increase durability. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. For the Slash 2WD. Retains all stock geometry for easy bolt up; no cutting or gluing required.

Completely sealed. An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Replaces weaker stock components, check for full parts compatibility. Backed by rPM's world-renowned breakage warranty. More clearance for larger pinions for owners hungry for speed.

RPM 80375 Front Bearing Carriers for Slash 2WD, Nitro Slash, E-Rustler and E-Stampede 2WD, Blue #ad - When used in conjunction with our #80382 rear bearing carriers, you’ll never have to worry about worn-out bushings or blown wheel bearings again! Tech notes: 5x11x4mm. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. Sleek contours that would look great on any vehicle.

Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede. Fits the traxxas slash 2wD, Nitro Slash, e-rustler and e-stampede 2WD. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm.

More information about HRPAA RPM80375 #ad


Similar products



RPM 73755 Front Bulkhead for Traxxas 1/10 2WD Vehicles, Blue

#ad
#ad
HRPAA RPM73755 #ad - An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Replaces weaker stock components, check for full parts compatibility. Retains all stock geometry for easy bolt up; no cutting or gluing required. Fits the traxxas slash 2wD, Nitro Slash, e-rustler and e-stampede 2WD.

We also cored out the bottom of the bulkhead. Made by rpm r/c products, a United States based company where resources are sourced from American producers. Our version is more that 15% lighter* than stock! by coring out the bottom of the bulkhead, it allows a convenient place to stick some modeling clay to adjust the weight bias of the truck.

RPM 73755 Front Bulkhead for Traxxas 1/10 2WD Vehicles, Blue #ad - The dust plate prevents build-up of dirt and debris, which could affect the handling and weight of the truck. Why? first and foremost, it helps the bulkhead sit flat. Replaces stock traxxas #3736; 5x11x4mm bearings not included. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede.

We also include a handy dust plate to cover the bottom of the bulkhead on vehicles such as the Rustler, Stampede and Bandit that leave the bottom exposed. For the Slash 2WD. It does not fit the 4×4 versions of any of these vehicles.

More information about HRPAA RPM73755 #ad


Similar products



RPM 80385 Rear Bearing Carriers for Slash 2WD, E-Rustler, E-Stampede 2WD and Bandit, Blue

#ad
#ad
HRPAA RPM80385 #ad - Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA! Replaces stock traxxas #3736; 5x11x4mm bearings not included. Made by rpm r/c products, a United States based company where resources are sourced from American producers. Identical in strength and performance as our #80375 front bearing Carriers, these rear carriers will get you to the finish line every time! Our bearing carriers are molded from RPM’s bulletproof blend of nylons and are guaranteed not break! Molded in black or blue.

Replaces weaker stock components. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. For the Slash 2WD. Replaces weaker stock components, check for full parts compatibility. Replaces stock traxxas #3752; 5x11x4mm bearings not included. Tech note: these a-arms will not work on the nitro versions of the Rustler and Stampede.

RPM 80385 Rear Bearing Carriers for Slash 2WD, E-Rustler, E-Stampede 2WD and Bandit, Blue #ad - Designed to increase durability. Backed by rPM's world-renowned breakage warranty. Backed by rPM's world-renowned breakage warranty. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

More information about HRPAA RPM80385 #ad


Similar products



Traxxas 3632A Blue-Anodized 6061-T6 Aluminum Caster Blocks pair

#ad
#ad
Traxxas TRA3632A #ad - Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter. Designed to increase durability. Designed to increase durability. This product is made from high quality materials and designed for long-lasting performance. Replaces stock traxxas #3736; 5x11x4mm bearings not included.

This is replacement hardware for use on Traxxas vehicles; consult your user's manual for exact parts listings. Replaces stock traxxas #2530 and #2530A. Made by rpm r/c products, a United States based company where resources are sourced from American producers. Traxxas #3632 aluminum caster blocks improve the appearance, and control on your Traxxas electric Rustler, ruggedness, 2WD Stampede or 2WD Slash.

Traxxas 3632A Blue-Anodized 6061-T6 Aluminum Caster Blocks pair #ad - Made by rpm r/c products, a United States based company where resources are sourced from American producers. Replaces weaker stock components, check for full parts compatibility. Quick and simple bolt-on installation. Proudly made in the USA. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used.

For the Slash 2WD. Completely sealed.

More information about Traxxas TRA3632A #ad


Similar products



RPM 80715 Front Caster Blocks for Slash 2WD, Nitro Slash, E-Rustler and E-Stampede 2WD, Blue

#ad
#ad
HRPAA RPM80715 #ad - Completely sealed. Rpm caster blocks are molded in our trademark blend of ultra durable and Super strong nylons and backed by the best breakage warranty in the R/C industry. The upper axle carrier hole. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

Each package contains one left side and one right side caster block. No additional parts or modifications are necessary to mount a set to a vehicle. Rpm caster blocks are redesigned to slim down unnecessary bulk while improving strength and durability in this heavily impacted area. Upgraded aluminum left and right 30-degree caster blocks provide improved performance and style.

RPM 80715 Front Caster Blocks for Slash 2WD, Nitro Slash, E-Rustler and E-Stampede 2WD, Blue #ad - To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Quick and simple bolt-on installation. Proudly made in the USA. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used.

. Rpm caster blocks for the traxxas slash 2wd, electric Rustler and electric Stampede 2WD are the final link for a complete, nitro Slash, bulletproof front suspension from RPM for these trucks.

More information about HRPAA RPM80715 #ad


Similar products



Traxxas 3741A Blue-Anodized Aluminum Turnbuckles and Camber Links, Front 39mm 2, rear 49mm 2

#ad
#ad
Traxxas TRA3741A #ad - Quick and simple bolt-on installation. An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. For use on the e-Rustler, Stampede, and Monster Jam. Aluminum turnbuckles blue-anodized. Use traxxas stock and hop-up replacement parts to get the most out of you Traxxas RTR vehicles.

Anodized 6061-t6 aluminum provides improved strength and light weight. Traxxas has grown to become the number-1 selling name in RTR nitro and electric models for the last 4 years running. Made by rpm r/c products, a United States based company where resources are sourced from American producers. Rpm is a proud american manufacturer designing and manufacturing 100% of our molded products right here in the United States.

Traxxas 3741A Blue-Anodized Aluminum Turnbuckles and Camber Links, Front 39mm 2, rear 49mm 2 #ad - Proudly made in the USA. For the Slash 2WD. Completely sealed. Made by rpm r/c products, a United States based company where resources are sourced from American producers. Designed to increase durability. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm.

Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

More information about Traxxas TRA3741A #ad


Similar products